Linksys SLM224G4S Manuel d'utilisateur télécharger pdf (Page 8)

Product Overview

Chapter 2

24/48-Port 10/100 + 4-Port Gigabit Resilient Clustering Smart Switch with 2 Combo SFPs

Chapter 2:

Product Overview

SLM224G4S

Front Panel

The Switch’s LEDs and ports are located on the front panel.

Front Panel of the SLM224G4S

System (Green/Amber) Lights up green to

indicate that the Switch is powered on.

Lights up amber while the Switch is performing a

system self-test. Blinks amber if the self-test fails.

LINK/ACT (1-24) (Green) Lights up to indicate

a functional 10/100 Mbps network link through

the corresponding port (1 through 24) with

an attached device. Blinks while the Switch is

actively sending or receiving data over that port.

Stack (G1-G4) (Amber) Lights up to indicate

that the corresponding port (G1 through G4) is

linked to another switch. (Two of these LEDs will

be lit if switch stacking is properly configured.)

LINK/ACT (G1-G4) (Green) Blinks when the

Switch is actively sending or receiving data over

the corresponding port (G1 through G4).

1000M (G1-G4) (Yellow)

Lights up to indicate a

functional 1 Gbps connection on the corresponding

port (G1 through G4) with an attached device.

Ethernet 1-24 The Switch is equipped with 24

auto-sensing, Ethernet network ports, which

use RJ-45 connectors. The Fast Ethernet ports

support network speeds of 10 Mbps or 100 Mbps.

They can operate in half- and full-duplex modes.

Auto-sensing technology enables each port to

automatically detect the speed of the device

connected to it (10 Mbps or 100 Mbps), and

adjust its speed and duplex accordingly.

G1-G4

The Switch is equipped with 4 auto-

sensing Gigabit Ethernet network ports, which

use RJ-45 connectors. The Gigabit Ethernet ports

support network speeds of 10 Mbps, 100 Mbps, or

1000 Mbps. They can operate in half- and full-duplex

modes. Auto-sensing technology enables each port

to automatically detect the speed of the device

connected to it (10 Mbps, 100 Mbps, or 1000 Mbps),

and adjust its speed and duplex accordingly.

miniGBIC (1-2) The miniGBIC (gigabit interface

converter) port is a connection point for a

miniGBIC expansion module, so the Switch can

be uplinked via fiber to another switch. The

MiniGBIC port provides a link to a high-speed

network segment or individual workstation at

speeds of up to 1000 Mbps.

To establish a Gigabit Ethernet connection using

a miniGBIC port, you will need to install a MGBT1,

MGBSX1, or MGBLH1 Gigabit expansion module

and use Category 5e cabling or fiber optic cabling.

To establish a Fast Ethernet connection using a

miniGBIC port, you will need to install a MFEFX1

(100BASE-FX) or MFELX1 (100BASE-LX) 100SFP

Transceiver and use fiber optic cabling.

Stack ID Displays the S

witch’s unit ID number if

the Switch is in stack mode.

Stack Master (Amber)

Lights up if the switch is

the stack Master during stack mode.

NOTE: On the SLM224G4S, MiniGBIC ports are

shared with standard ports. If a miniGBIC port is

used, then the shared standard port on the Switch

cannot be used. The following table defines the

shared port mapping of the SLM224G4S Switch.

SLM224G4S Shared Port Mapping

miniGBIC Port Standard Port

miniGBIC 1 G3

miniGBIC 2 G4

Back Panel

The Console port and power port are located on the back

panel of the Switch.

Back Panel of the SLM224G4S

CONSOLE The Console port is a serial port that

allows you to connect to a computer’s serial port

(for configuration purposes) using the provided

serial cable. You can use HyperTerminal to

manage the Switch using the console port.

POWER The Power port is where you connect

the AC power.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 76 77

Commentaires sur ces manuels

Pas de commentaire

Linksys SLM224G4S Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires pour ordinateurs Linksys SLM224G4S