Linksys EG0801SK Manuel d'utilisateur

Instant Gigabit SeriesEtherFast®10/100/1000 8+1 WorkgroupGigaSwitch Starter KitUser GuideUse this guide to install :EG0801SK

Installing the Drivers forWindows 95After installing the Instant Gigabit NetworkAdapter in your computer, follow theseinstructions for installing the

3. If you clicked the Other Locations button, this window will appear. Entera:\win95. Windows will begin copying the Network Adapter’s driver filest

Installing the Drivers forWindows 98OverviewAfter physically installing the Instant Gigabit Network Adapter in your com-puter, follow these instructio

6. A window will open saying that Windows is now ready to install the LinksysEG1032/EG1064 Instant Gigabit Network Adapter driver. Click Next.7. Windo

Installing the Drivers forWindows MillenniumAfter physically installing the Instant Gigabit Network Adapter in your com-puter, follow these instructio

6. At this point, the installation may require files from your WindowsMillennium CD-ROM. If prompted, insert your Windows Millennium CD-ROM into your

Windows NT 4.0 Installation &SetupThe following instructions will set up the Instant Gigabit Network Adapter in acomputer running NT 4.0 server/wo

5. Highlight the Linksys EG1032/EG1064 Instant Gigabit NetworkAdapter entry in the window that appears. Click OK. 6. The adapter will be added to th

9. NT will probably ask you to supply your original Windows NT CD-ROMor setup disks. If so, place your Windows NT CD-ROM in your CD drive.If the CD-R

13. Click Finish. When asked if you want to restart your computer, remove theDriver Disk and click Ye s . 14. Once your PC has rebooted and you are lo

COPYRIGHT & TRADEMARKS Copyright © 2001 Linksys, All Rights Reserved. EtherFast is a registered trademark ofLinksys. Microsoft, Windows, and the

3. When the list of available network adapters appears, click the Have Disk but-ton. 4. Put the Instant Gigabit Network Adapter disk into drive A. Typ

8. Click on the Protocols tab. Add any protocols you require by clicking theAdd button. (Refer to your Microsoft documentation if you have any ques-ti

3. Windows will display the Welcome to the Found New Hardware Wizardbox. Click Next.4. The Install Hardware Device Drivers dialog box will appear. Wh

6. The Driver File Search Results dialog box will appear. Click Next.7. The Completing the Found New Hardware Wizard dialog box willappear. The follo

Network Address:Allows the user to configure the network address of the adapter, rather thanusing the one in ROM. If not specified, the address on the

2. The Network window will appear (below).Click on the Configuration tab. A windowsimilar to the one below will appear. Theremay be other components

11. Optional: Choose theAccess Control tab.Ensure that Shared-levelaccess control is selected.If the setting is on User-Level access control andyou c

AppendixOverviewBy sharing your files and printers, other PCs on your network will be able toaccess the resources on your PC. Before sharing your file

1. Windows 95 will detect the Instant Gigabit Network Adapter and display aNew Hardware Found window. 2. Insert the Instant Gigabit Network Adapter

If you experience installation difficulties, you may need to re-install all of theWindows networking components from scratch. The instructions below e

ContentsIntroduction 1Your EtherFast®10/100/1000 8+1 Workgroup GigaSwitch 1Features 1Package Contents 2System Requirements (for the PCI Adapter) 2Get

5. For PCs with Dial-Up Networking and/or an AOL adapter, remove anyinstance of the name Linksys, all IPX/SPX protocols, all NetBEUI, allClients, and

1. Click the Start button, choose Settings, choose Control Panel, then double-click the System icon.The System Properties window will open.2. Choose

8. Right-click on Linksys EG1032/EG1064 Instant Gigabit NetworkAdapter again. This time, select Uninstall. Click OK.9. The Network Adapters category

IPX/SPX-compatible ProtocolClick the Add button. Choose Protocol and click the Add button. SelectManufacturer and choose Microsoft. Under the Network

When a PCI card is used in a computer that supports Plug-and-Play, the card isautomatically configured each time the computer is booted. The card&apos

TroubleshootingThis section provides possible solutions to problems regarding the installationand operation of the Instant Gigabit Network Adapter. If

10. In Network Neighborhood you can only see computers running the same oper-ating system as your computer (i.e., your PC is running Windows 95 and it

Glossary10BaseT - An Ethernet standard that uses twisted wire pairs.100BaseTX - IEEE physical layer specification for 100 Mbps over two pairs ofCatego

DHCP uses the concept of a "lease" or amount of time that a given IP addresswill be valid for a computer. The lease time can vary depending

IPCONFIG - A Windows NT or 2000 utility that provides for querying, defin-ing and managing IP addresses within a network. A commonly used utility for

• One Instant Gigabit (32-Bit) Adapter• One 10/100/1000 8+1 Workgroup Gigaswitch® • One Category 5E Network Crossover Cable (10 ft.)• One 3.5” Driv

STP (Shielded Twisted Pair) - Telephone wire that is wrapped in a metal sheathto eliminate external interference.Subnet Mask - The method used for spl

SpecificationsModel EG1032Standards IEEE 802.3, IEEE 802.3ab, IEEE 802.3xPCI 2.1, PCI 2.2, ACPIProtocol CSMA/CDPorts: 1 Straight-Through10BaseT/100Bas

EG1032Dimensions 6.3” x 4.3” x 1.4” (160mm x 110mm x 35mm)Unit Weight 9 oz. (.25kg)Power 3.3VDC, 3ACertifications FCC Class B, CE Mark CommercialOper

Contact InformationFor help with the installation or operation of this product, contact LinksysCustomer Support at one of the phone numbers or Interne

© Copyright 2001 Linksys, All Rights Reserved.Printed in the USA.http://www.linksys.com

The LED IndicatorsPower Amber. The Power LED lights up when the Switch is pow-ered on.Link/Act Green. The Link/Act LED serves two purposes. If the LED

Planning Your NetworkBuilding a Gigabit network involves more topology rules in addition to the10BaseT/100Base-TX network rules. These rules specify

If you are setting up a network for the first time, or if you already have a10/100 BaseT network without Gigabit capability, you may be wonderingwhich

Installing the EtherFast®10/100/1000 8+1 WorkgroupGigaSwitch Starter Kit onto YourNetworkInstalling your Starter Kit will involve installing both the

Connecting Computers To Your SwitchYour Switch’s rear panel has eight standard RJ-45 ports, plus a Gigabit port.Each 10/100 port automatically detects