Linksys EFG80 Manuel d'utilisateur

Instant GigaDriveTMSeriesEtherFast®NetworkAttached Storage with 80 GB Hard Drive + PrintServerUser GuideUse this guide to install: EFG80

7. From the next screen, Figure 4-8, you can change the time and date on theInstant GigaDrive™. IP Address. Set the Instant GigaDrive’s IP Address her

10. You have now successfully set up the Instant GigaDrive™ with the SetupWizard. When the screen shown in Figure 4-11 appears, click the Exit but-ton

Chapter 5: Using the InstantGigaDrive’s Web-Based UtilityFor your convenience, an administrative utility has been programmed into theInstant GigaDrive

If you have not already assignedan administrative user name andpassword for the Adminstrator,you can enter the default username of Administrator. Ther

From the LAN screen, you will be able to configure some of the settings yousaved from the Setup Wizard. While these changes are being made, you cancli

OPTIONSConvert Failed Logins With this enabled, the GigaDrive will automaticallytake any failed logins (user name and password) asguest logins, provid

Properties Enter the user’s name in the Name field. Punctuation and otherspecial characters (e.g. * / | \ ) cannot be used in the name. Inthe optional

The Status Information screen, shown in Figure 5-11, allows you to check thedetails and status of the Instant GigaDrive™.System GigaDrive Name - The c

E-Mail Alerts Check the Send button to enable the sending of E-Mail alertsby the Instant GigaDrive™. Alerts will be sent when there issome problem req

The Shares Information screen, shown in Figure 5-14, allows you to create andmanage shares.Existing Shares Click the Access button to view and configu

COPYRIGHT & TRADEMARKS Copyright © 2002 Linksys, All Rights Reserved. Instant GigaDrive is a trademark ofLinksys. EtherFast and Linksys are regist

The Disk Settings screen, shown in Figure 5-16, allows you to perform diskmaintenance.As shown in Figure 5-15, the Backup Settings screen allows you t

As shown in Figure 5-17, the Upgrade screen allows you to upgrade theFirmware to the Instant GigaDrive™.Current Firmware This shows you the current ve

3. When I click the Instant GigaDrive’s icon in Network Neighborhood, I’mprompted for a password.This can happen in the following situations:• Your W

5. Attach the power cable from the drive tray toyour hard drive, as shown in Figure B-3. Thepower cable is the smaller of the two cablesin the drive t

10. Lock the tray into the GigaDrive’s bay, as shownin Figure B-8. The tray must be locked in for theGigaDrive to properly function.11. Plug in the Gi

5. Click the Add Printer icon, shownin Figure C-4. This will open theAdd Printer Wizard.6. When the opening screen tothe Add Printer Wizardappears, sh

EtherFast®Network Attached Storage10. From the Add Printer Wizard screen, shown in Figure C-9, select yourprinter’s manufacturer from the list on the

Appendix D: Glossary10BaseT - An Ethernet standard that uses twisted wire pairs.100BaseTX - IEEE physical layer specification for 100 Mbps over two pa

FTP includes functions to log onto the network, list directories and copy files. Itcan also convert between the ASCII and EBCDIC character codes. FTP

PrintServer - A hardware device that enables a printer to be located anywherein the network.RJ-45 (Registered Jack-45) - A connector similar to a tele

Instant GigaDriveTM Series EtherFast®Network Attached StorageAppendix D: Glossary 48Appendix E: Specifications 54Environmental 54Appendix F: Contact a

54EtherFast®Network Attached StorageAppendix E: SpecificationsModel Number EFG80Standards IEEE 802.3, IEEE 802.3uProtocols SMB/CIFS over TCP/IPNetwor

Appendix F: Contact and ReturnsInformationFor help with the installation or operation of the Instant GigaDrive™, contactLinksys Customer Support at on

EtherFast®Network Attached StorageThe following items, shown in Figure 1-1, should be included in the InstantGigaDrive’s packaging.• One Linksys Insta

Reset Button If the Instant GigaDrive’s IP Address or password is lost,press and hold this button down for three seconds, thenrelease this button. The

EtherFast®Network Attached StorageThe Instant GigaDrive™ has an internal beeper that beeps to indicate certainevents. 1 Beep This signals that the Re

EtherFast®Network Attached Storage5. Locate the Instant GigaDrive’s power switch on the rear panel. Press it onceto power on the Instant GigaDrive™.

EtherFast®Network Attached StorageThis Welcome screen provides you with four options in the buttons alongthe right side of the screen. The first butto

The Fixed IP Address is set by default (192.168.1.77). Use this setting ifthere is no DHCP server on your network and you want the InstantGigaDrive™ t